ABS Plastic DC24V UV Fire Alarm Flame Detector for High-Risk Environments

• Customization: Available
• Type: Smoke Alarm
• Signal Transmission: Wired Alarm
• Model NO.: XHARS602
• Working Mode: \
• Certification: CE
• Application: Indoor, Outdoor
• Working Principle: \
• Transmission Mode: Relay Output
• Alarm Volume (within 1m): ≥80dB
• Receive Frequency: \
• Spectrum: 180~290nm
• Relay Contact Load: 1A@DC24V
• Protection Rating: IP21
• Operating Voltage Range: 12 to 28 VDC Volts
• Detection Sensitivity: Level 1 25m
• Detection Angle: 120degree
• Transport Package: Carton
• Specification: 103*103*45mm
• Trademark: XHA
• Origin: China
• HS Code: 8531100000
• Production Capacity: 500000pieces/Year
• Package Size: 10.30cm * 10.30cm * 4.50cm
• Package Gross Weight: 0.130kg

Product Description

High-Standard Fire Alarm Flame Detector With 12-28 VDC Operating Range

 

Introduction

 

The DC24V Ultraviolet Flame Detector is a specialized sensor designed to quickly detect the presence of flames in high-risk environments. It utilizes ultraviolet (UV) light sensing technology to identify the unique UV radiation signature emitted by burning substances, providing fast and reliable fire detection capabilities.

Specification
 

Operating Voltage Range: 12 to 28 VDC Volts

Standby Current: ≤10 mA @ 24 VDC

Alarm Current ≤30 mA @ 24 VDC

Spectrum: 180~290nm

Detection Angle: 120 degree

Detection Sensitivity: Grade I, 25m@flame (Container 33cmX33cm,Height 5cm with 2Kg ethanol )

Relay Contact Load: 1A@DC24V

Normal Status: LED blinking in 5 seconds interval

Alarm Status: LED lit steady

Operating Humidity Range: 10% to 93% Relative Humidity, Non-condensing

Operating Temperature Range: -20°C to 55°C

 

 

Installation
 

NOTE: All wiring must conform to applicable local codes, ordinances, and regulations. Mounting Indoor Wall or Ceiling Products.

1. Attach mounting base to ceiling or wall.

2. Connect field wiring to terminals:

Terminal 1: Relay Output -COM (ZONE+)

Terminal 2: Relay Output - NO/NC (ZONE-)

Terminal 3: DC Power -

Terminal 4: DC Power +

3. To attach product to mounting base.

4. Secure product by tightening the two mounting screws in the front of the product housing.

5. The detector can be connected with Security alarm panel as Figure3. Relay output signal can be changed from Normal Close (NC) to Normal Open (NO) by Jump JP1 on the PCB board.

6. The detector can be connected with conventional alarm panel as Figure 4. One 4.7K ohm resistor should be connected as End of Line (EOL) resistor at the last detector.

7. After the installation, power on the detector, use lighter or candle to test the detector within 3 meters.

WARNIING:

Not to install flame detector near the below subjects:

1. Halogen lamp, Electric discharge lamp, ultraviolet ray lamp.

2. Welding spark, Electric spark

3. Heavy current magnetic field, thunder discharge.

4. Direct sunlight.

5.Ultra violet radiation subjects
The UV flame detector can not detect the following:

1. The flame behind the glass or transparent resin.

2. Lighted cigarette.

3. Burning charcoal and coal cakes.

4. Burning material without flame.

Application in Conventional Fire Alarm system

Product Range

Conventional Fire Alarm System
Addressable fire alarm system
Gas Extinguishing control system
Beam Detector
4 wire smoke detectors with relay output.
2 wire Conventional smoke and heat detectors
Explosion-proof flame detector for fire alarm system
Standalone smoke detectors and combustable gas detector



Service

1. OEM &ODM service.
2. Provide technical support and after-sale service.
3. 1 year warranty.
4. Normally 15 working days lead time.
5. Welcome sample order.

Conpany Profile


Assembly Line


Burn-in Room

Quality Management System